FLM02B / version 250, inconsistent number of sensors, only 2 sensors in dash

by limpens on

Hi,

My FLM is not reporting properly anymore, syslog shows it is only reporting data for one part of the smart-main sensor and a single (out of three) current clamp.

Looking at /usr/share/tmpo/sensor, 9 different sensor directories show up. Running uci show, it reports the same number, but different id's.

/usr/share/tmpo/sensor:

  1. drwxr-xr-x    3 flukso   flukso           0 Jan  1  1970 05490a263ec9d808793a727ed032c1e8
  2. drwx------    3 flukso   flukso           0 Apr 11 21:03 2dfca47874bf58d00bd61f22abe60888
  3. drwxr-xr-x    3 flukso   flukso           0 Jan  1  1970 437a8ab0b2cb46bfc0cce3b4b10ea455
  4. drwx------    3 flukso   flukso           0 Apr 11 19:07 46015085633fca582cc4ce01c93fb4be
  5. drwxr-xr-x    3 flukso   flukso           0 Jan  1  1970 83528867422c2453f1060eb2c6f1bb7c
  6. drwxr-xr-x    3 flukso   flukso           0 Jan  1  1970 8b47cce4a538517632dfb0b8e39b0962
  7. drwxr-xr-x    3 flukso   flukso           0 Jan  1  1970 cb309c065baae0f05b7d4ffa035b8b38
  8. drwxr-xr-x    3 flukso   flukso           0 Jan  1  1970 e8710ccf91b912050f0ea0da82378112
  9. drwx------    3 flukso   flukso           0 Apr 11 20:03 f2c388864453ae8ed989128d5a43f5ab

Output from uci show:

  1. flukso.1.id=83528867422c2453f1060eb2c6f1bb7c
  2. flukso.2.id=8b47cce4a538517632dfb0b8e39b0962
  3. flukso.3.id=437a8ab0b2cb46bfc0cce3b4b10ea455
  4. flukso.4.id=e8710ccf91b912050f0ea0da82378112
  5. flukso.5.id=4258e70b4b81f67f607bb1419ebbc495
  6. flukso.6.id=40c4956d7c5c779cdbefaa93f76c5173
  7. flukso.7.id=cb309c065baae0f05b7d4ffa035b8b38
  8. flukso.8.id=05490a263ec9d808793a727ed032c1e8
  9. flukso.9.id=46015085633fca582cc4ce01c93fb4be

The only sensors shown in the dash include 83528867422c2453f1060eb2c6f1bb7c (L1) and (probably) f2c388864453ae8ed989128d5a43f5ab (smart-main)

In the flm UI, 'Sensor config synchronisation' reports a successful sync at 11/4/2018, however saving the
sensor configuration reports an error:

  1. Syncing configuration: gh 266 0 .. ok
  2. Hardware check (major: 266, minor: 0) .. nok
  3. Error. Major version does not match.
  4. Use -f to override this check at your own peril.

Is someone able to tell me how to resolve this situation? I used to see 6 sensors (L1, L2, L3, electricty from smart-main, gas from smart-main and water)

Sincerely, Eric

‹ disabeling the dhcp server? sensor board hardware compatibility check failed Internal error ›
limpens's picture
limpens |

@icarus75: any change you could look into this? I've not been able to submit proper sensor readings for over a month.

Sincerely, Eric