Hi,

I am sorry if I come across like a newbie but after spending 2 hours reading different topics in the forum I am still not sure how to change basic things on my new Fluksometer. All I want to do is connect my fluksometer to my router using a cat5 cable. So I only need to change the fixed IP address of the FLM and disable the DHCP. Where do I start?

There is that discussion https://www.flukso.net/content/no-ip-connect but it seems a little old and I am afraid to corrupt my new Flukso.

Can please anyone give me some directions?

Thanks
Luke

Similar as the thread you just closed. Ive just added a Gas sensor. Hall effect. I Can see pulses at FLM terminals, .15v to 3.2v when I pass a magnet next to sensor.
Nothing on sys log though?
Is this voltage change enough?

From prev thread:
ICARUS75 | TUE, 01/07/2014 - 19:50
The problem with your ports 2 and 3 not showing any data were due to a server-side provisioning error. Should be fixed now. Can you confirm by doing the tap test one more time? You should see data appearing on the hour chart within five minutes after running the tap.

Forgive me: I know this is an issue which is posted several times in this forum, but I tried really everything which is proposed as a solution and till now no success: the minute graph don't show up. I can't imagine that I'm the only one who have problems with this....

I know it's a problem with browsers and mixed content.

I tried several combinations:
- on Windows 7 with IE 11, Chrome 35 and FF 30;
- on MAC OS X 10.9.3 with Safari, Chrome 35 and FF;
- iPad;
- iPhone.

Each time mixed content has been enabled (as proposed as the ultimate solution) but only the well known message "timeout and not in the same local network" appears but no minute graph....

I work with a FLM v2b and I'm getting the 200 status code for the GET request.

Please some help to make the minute graph work, I'm getting a little frustrated....

Thanks!

I recently installed a FLM2. I have a 3 phase installation (belgium) and 3 clamps attached on the 3 phases (checked by my electrician and according to him right attached).
Configuration FLM: 3 phases - 3 clamps 50 A - 230V
Connection clamps in serie (so no wires on port 3): see attached photos

Problem: the measuring is much too low. For instance: yesterday i measured 8,018 kWh on the FLM while the official company meter indicates a consumption of 13,430 kWh.

What can be wrong here?

Thx for the help.
Joost

I just added to my Flukso V2b a water pulse sensor number 3 to my two other pulse existing electricity sensors. I set the clamp ports number to 1 so all the other ports 2-5 are pulse ports.

Water Pulse Sensor 3 http://i1289.photobucket.com/albums/b503/Molari1/WaterSensor3_zps270f5f9...
Solar Production Pulse Sensor 4 http://i1289.photobucket.com/albums/b503/Molari1/SolarProductionSensor4_...
Home Usage Pulse Sensor 5 http://i1289.photobucket.com/albums/b503/Molari1/HomeUsageSensor5_zpsb2d...

The syslog below shows that the Flukso is receiving the pulses from the water sensor but I cannot see the pulses in the Dash nor in PVoutput. In the Dash I am receiving in Hourly and Daily display an error:
"Error - No water sensors to display. Please select another sensor type.
"The electricity sensors are working properly as I see it.

Syslog http://i1289.photobucket.com/albums/b503/Molari1/FluksoSyslog-HomeUsagea...

PVoutput Water Extended data http://i1289.photobucket.com/albums/b503/Molari1/PVoutputWaterExtendedda...

As I remember when I set up my Flukso in mid April and connected the electricity sensors to inputs 2 & 3 they did not work but when I switched them to outputs 4 & 5 they work properly. I am therefore wondering if my Flukso V2b is faulty or there is any other thing that I not setting right.
Tx